Daggerboard trunk glued up and rear seat glued on

Ok my patient mates, heres some photographic evidence of my work on the boat last week before I left for self-imposed exile at work.

First, I finally got that bedamned daggerboard trunk glued up.  Somehow, I wasnt forward thinking enough, and I glassed up the daggerboard without really giving much thought to how it fit in the already made trunk.  Well, I did but discounted further planing on of the daggerboard and decided that I was done with all the planing and sanding thank-you-very-much and whatever I had, I had.

This was most unfortunate, because I few more minutes of planing would have produced a superior quality board, and it would have fit in my daggerboard case.  So then I was stuck with the project of widening my case, but only by 2-3mm at most because really, all I needed was 1-2mm.

Fortunately, I found 3mm Okoume marine plywood at Goose Bay Lumber, and cut it to fit over the framing for the trunk.  This widened the trunk appropriately.  Here is the widening sequence in pictures:

Very self-explanatory, I think.

Next, I still struggle with the hardward issues for the rudder and transom gudgeons.  I dont know how Im going to get this rudder assembly attached to the boat.  The problem is that the hole to accomodate the tiller does not have the vertical clearance required to use a gudgeon-pintle scheme, which is by far the most convenient.  I toyed around with it and thought about enlarging my tiller-hole, but my pintle arms didnt fit around the rudder cassette.  A second order of larger, more heavy-duty gudgeons for rudder and transom fit great, except not with each other, and the arms were too long for the spacer in the cassette... A rod pushed through the gudgeons would not have fit cleanly and I would have had a clunky feeling rudder, the round peg in an oval opening thing, if you can visualize that.  So I still sit, wondering how I will fix this conundrum.  Many people have done it successfully, but Im still hunting around for the best hardware.

Because of all this drama, I have delayed gluing on the rear seat.  I got tired of having it loose, and glued it on before I left.  Here, yet again, is my "Forest of Bricks" holding it all down.

And the gratuitous parting shot:

Rudder stock design 4 Mast gluing

In yet another installment of "I try to re-design the rudder stock" I have received yet another set of plans from a Goat Island Skiff builder in New York.  He has graciously supplied me with these two schematics of his own design, as a solution to removing the tiller from the rudder assembly without having to take the rudder off the transom.  It is self-explanatory:

I really like this design, it is better than mine for two reasons:  1. It maintains Mr. Storers rudder stock design and hopefully solves the structural issue that he was concerned about, 2. There is less time fiddling over the transom pulling very critical pins over water of yet-to-be-determined depth, if you get my drift.  I can remove the tiller from the safety of the cabin.  Unfortunately, I will still have a stub of tiller sticking into my domain, but I think, for now, this is the idea Im going to go with.  The great thing about the rudder stock is that it is simple and easy to construct, I can always make another.

In other news, the mast was glued in its first step today.  In the previous post, I shaped the narrow staves.  This was a workout, but I worked carefully, and Im happy with the result.  Then, off to make the spacers for the ladder frame.  I used a piece of fir that was lounging around the garage, some stud material.  I used some good parts, and cut them to fit.  The base plug meant a trip to Lowes.  This is the first wood part of the boat that was not bought at either of my two local lumber stores.  Sorry guys.  Anyway, an 8 piece of 4x4 cedar.  I thought about using fir, for a few bucks less, but I went with the rot-resistant cedar.  Its an important piece, its light, and it should be good.  The other spacers Ill goo up with epoxy and make them plastic.

Well, that was interesting how the photos lined up, but I like it!  Notice the base plug.  After a quick mock-up my lovely wife and I took one of the uncut stave stock pieces and brought it into the basement, where I can get an even floor workspace and a slightly higher temperature, better for quicker gluing.  We made sure that we could get the wood in and out of the basement two different ways, so I dont build the mast and then get it out.  I am positive I can get the mast out of the basement.

Layed out ready for the dry fit:

Sweet, I did it again, but I dont know how.  The mast is quite straight, but I decided to use one of the wide uncut staves as a backbone for gluing, that way I could ensure that the mast is straight with no wobbles.  It also gives me a good even workspace for gluing too.  I covered one stave with packing tape, and glued away:  Notice too, the hardwood runners that will be glued to the bottom of the hull, they are long ones and needed to be scarfed.

It went well.  The bricks are slightly nudging the mast into a straight position.  Youll also notice that you dont see much of the wide stave underneath this glue-up, thats because the tolerances are super tight.  I overcut my narrow staves by 1mm and it pretty much ate up all the space on the wide stave.  I briefly considered re-planing the staves, re-working the spacers, and then gluing, but my lovely wife stopped me with some business graduate degree mumbo-jumbo stuff and talked me out of it.  I might have to plane a little extra off the base to get it to fit in the mast step, and I can (with difficulty) enlarge the mast step as well if need be.

Tomorrow, gluing the wide staves and completing the box.
 

Painting Top Coat

This is a big post.  Big as in:  Holy Baloney Batman, were getting close to the end!  Goat Island Skiff, activate!

After priming my boat, I had to leave for work.  I got home 5 days later, gave it a good smoothing sand job, and then cleaned up the dust with the shop-vac blower to vacuum to rag soaked in denatured alcohol.  The denatured alcohol was a tip mentioned on the Wooden Boat Forum-- it will help soak up and evaporate any water that had absorbed into the primer as well as clean up dust.  After that, it was time for painting.

The paint was Interlux Brightside, a one part marine paint.  Its expensive, about 40 bucks or so a quart depending on where you purchase it.  I decided to use the pricey stuff as opposed to Behr Porch Paint or Rustoleum Enamel because I figured Ive spent so much money on this boat already, I might as well use good paint on the exterior as well.  Its just a bit more anyway, and it was well worth it, as you will see.

I used a roller, which left behind little bubbles, and then "tipped-off" with a bristle brush.  I would generally roll vertically and then gently tip-off with a brush horizontally.  Then I let it dry.  The instructions recommend sanding with 320 before the second coat, but I only had 220 and used that, with little ill effect.  A second coat then was applied, and the results are spectacular.  Behold, my painted boat:

Not bad!  Check out the reflection of the towel!  It looks like gel-coat!  I am the painting man, thanks to Interlux Brightside and its easy-to-apply-million-dollar-finish qualities!

Next up, the interior, and sailing.

For the super vigilant, they will notice I still do not have rudder hardware on the stern.  This is bad news, and there will be a post devoted to rudder hardware, Duckworks (awesome), and West Marine (awful evil disgusting chain store I will never frequent again).

Let me just say this, if my boat gets finished and I dont have rudder hardward and this impedes me from sailing, I am going to freak out.

Knees closer up rear seat inspection hatches

So earlier this month I neglected to show some closer up pictures of the knees and the breasthook.  Here they are.  You may notice that I chose to not stylize the knees in any fashion, as other Goat Island Skiffs do.  I am a big fan of straight lines, utilitarianism, and functionality.  (Also WPA artwork and air travel posters from the early 20th century, for very much the same reasons.)  Curvy knees and breasthooks are nice, but I dont think they deliver the straightforwardness I enjoy in design.  Obviously, this is personal preference.  Curvy knees can look fantastic.  The stem in the bow will be cleaned up at some point, maybe a small cover.

Today I also added the locations of my inspections ports.  I have chosen an 8" Beckson screw-in inspection port for easy ingress and egress of larger items.  The smaller 6" port is for access to the rudder gudgeon fittings.  It is off-center due to the seat cleat that runs down the middle of the compartment from BH4 to the transom.  This could have been circumnavigated had I thought about it beforehand, but I didnt, so this is what I get.  Not the end of the world.

Finally, a quick look on how I glued the knees in place:  Two tape covered shims held in place by clamps for vertical support, and the clamp just to weight it up against the side of the hull.  Not too much weight is needed, because the knee could slide up, also, if its beveled correctly it wont slide down.

West Marine Thieving Scumbags

I ordered some small parts (gudgeons for my rudder) for my boat from West Marine.

I received an email stating that the items have shipped.

I received an invoice in the mail stating the items have shipped.

After 10 days I called, looking for my parts.  "Theyre coming."

After 20 days, I called, looking for my parts.  "Call back next week."

I call back today, and they tell me that the items have not shipped.  They dont even have the items in stock.  There is no timeframe available when the items may be in stock.

They have my money, and I dont have any parts.  Need to find alternative plans now.