My big day

Today was quite the day. Im over my cold, as in, I dont feel like super-crap anymore, but my head and chest are still congested to hell and back. However, since Im slowly on the up and up, off to the basement for a little R+R.

Last night I realized that I had beveled the bottom of BH1 in the wrong direction. Today I fixed this by re-beveling it flat, and just leaving it as such until later. If I have to bevel it in the correct direction, so be it. Its only 2mm so its not too tricky.

Second, I found this:

Delamination in the ply on my Starboard bow, inboard. Approximately 4"x6" or so. Nothing on the "mated" side, the Port stern, so Im assuming it is only this piece that has the problem. I sounded it out with a pencil, and Ive got a good idea of its shape. I poured straight epoxy into the hole, then squashed it with bricks.

Third, I discovered this:


Thats my finger pointing at where the bow SHOULD be. OOPS. Im slowly coming along with the dreaded stem, and I went to match the stem to the bow and it came up a couple of cm short. Either my stem was wrong or my bow was wrong. I busted out the lofting map for the sides and for some damn reason, I measured 55mm from the end of the ply to the point of the bow rather than 55mm from the last 300mm mark. Damn, bro, good catch! So I re-marked the bow and cut them anew on both sides. The stem fits perfectly now, with room to spare for the bow knee.

Then, I got gutsy and ripped two of my cedar planks and and scarfed them for the chinelogs:

This is my scarf. Some of you are really going to hate this, but I eyeballed it on the table saw, and then planed them to match. Not perfect, but close enough for this amateur! I used a 1:6 ratio, so that would be 1 1/2" : 9".

THEN, I cut out the buttstraps and glued my scarfed chinelogs and my side together!


Here we are now in the garage. The buttstrap gluing kinda blew, I was by myself and I rushed it. I was sure I put on enough glue, but very little actually oozed out from underneath the straps. Im actually a little concerned I may not have put enough, but maybe I put just the right amount, I tend to go overboard with the glue. So well have to see about this.

Finally, I glued on a little piece of ply for backing on the transom for el rudder. Thats Spanish. That in itself was a mini-adventure, because the ply I chose for it initially starting sliding around after I glued it up on the old epoxy from the frame and the seat cleat. WOOPS. So I pulled it off quick, tore apart the garbage for an old jigsaw blade, and holding the jigsaw an inch above the ply ripped a small piece of one end so it could sit better between the frame and the cleat. Of course I got wood dust all over the backing, and I scraped it off, threw on some thickened epoxy, and called it good. I thought this would have been a simple operation, so I didnt wear gloves and holey moley my hands got sticky.

On a blog-related note, I am deleting the timing scoreboard from the blog. Its beginning to get inaccurate and more difficult to keep up with. Today I did a million things and Im not keen on attempting to figure out what was what. So maybe from now on just a tally total.

Some really good reading about a seriously good cruise in a pair of open boats

There are days when being an “armchair admiral” is not such a bad thing.  To sit warm and comfortable, listening to the wind shrieking and laughing at you as it tears through the trees with the driving rain rattling on the windows and shaking the doors is a very pleasant thing.  It’s a time to dream of warm days, sparkling water, golden beaches and gentle breezes.  Of meeting people who enjoy the company of small boat sailors, exploring places where one can pretend that no human has ever been before, seeing new vistas every hour of every day and  watching spectacular sunsets before retiring to a comfortable bunk and listening to the water lapping at the side of the boat.

Its such a day here, springtime, and I wont go on about it because I’ve said it all before, springtime can bring tough weather here.  But I’ve been sitting in my bunk, the boat surging at its dock lines, the wind doing all that stuff while I read this wonderful account of a cruise in a pair of “my” boats in Shark Bay, waaay north of Perth in Western Australia.  It’s a great story, well written, well illustrated with both pics and video, so get your coffee made, sit down in a comfortable place, and read on.

http://www.gaffrigsailinginwa.org/shark-bay-001

Many thanks to Author Paul Ricketts and cruising companion Peter Kovesi for sharing this, and to the “open boat” Yahoo group from which I got the above link.

Great stuff guys, keep up the good work.

Panama City to David

Its been an interesting three days trying to get to remote Bocas del Toro. Flight delays, missed connections, holiday travelers, etc. have conspired to keep us from reaching our destination, but we are pretty sure that with a little ingenuity well finally reach Almirante tomorrow, where we can catch a water taxi to Bocas Town. From there its a short ride in a panga to Bastimento Island, where the Red Frog Marina is located. We left Puerto Vallarta on the 28th and I expect to arrive at the Red Frog a few minutes before the new years eve festivities begin.

Right now were in the city of David (pronounced daveeed). The ride, around 350 kilometers in a taxi, took us through the heavily industrial parts of Panama city, through rough looking suburbs, and then through wildly beautiful tropical countryside. Looking out the windows of the truck that served as our taxi, we saw people living in squalid tin-roofed shacks, caballeros astride beautiful horses tending their herds of brahma cattle, poor people trudging along the road carrying all manner of things, including chickens in cages, sides of beef, and other small caged animals. At one point we passed an overturned tractor trailer that had split open and kids were taking cases of soda that had burst from its seams. At another point, we passed a scene where the police had captured, handcuffed and roughed up two men alongside the road. Life in Panama is a long way from how we live in Orange County.

I just finished reading David McCulloughs fascinating book, "Path Between the Seas". Its an account of how the Panama Canal was built and the forces, political, economic and military that were brought to bear to accomplish that stupendous feat. Just as important to humanity was the discovery and implementation of effective means of controlling and eradicating yellow fever and malaria in ths region. The USA played a key role in the founding of the Republic of Panama and has been involved in many of this countrys most important historical milestones, from Teddy Roosevelts support for its secession from its mother country of Colombia in 1903 to George 41s decision to invade the country and capture Manual Noriega, Panamas president, in 1989. That particular adventure was called Operation Just Cause.  I suppose it should be no surprise that the local people of this country have shown us little of the buoyant friendliness that we have constantly experienced in Mexico, but I should also say that in spite of the delays and frustrations of our travels, weve been enjoying our time here. Delays are part of travel everywhere in the world at this time of year, and were very glad that its not snowing and freezing here. Wherever you are, have a rockin good time ringing in the new year!

A note on tools

A few things on tools that I have found out the past few days.

A japanese pull saw is awesome. I doubted it at first, hemming and hawing for months before getting a small one-sides saw. A FANTASTIC PURCHASE. Versatile, sharp, easy to use, and precise. Practice first, because youll saw through something important quickly and without realizing it (trust me).

My random orbital sander was a $9.95 DEATH DISASTER I purchased at cheap-tool-emporium Harbor Freight. Its so frustrating to use I want to throw it at the cement wall. I will have to go buy a better one that actually secures the sandpaper.

Most importantly, I was perusing my jigsaw blades and saw something called a "scrolling blade." It was small and skinny. "Hmmmm, I betcha this is for going around corners a little tighter than the normal blades!" Hmmmm, I reckon I was correct... and this was after I cut the hole through the transom, BH2 and BH3. Boo me, for not knowing my tools. Again, amateur style is my building style.

Gluing BH 4 and some things I found out about gluing

Alright, Im a little frustrated at myself right now, because things are coming along nice, but not coming along like I want them too. Everything will be OK in the end, but it wont be as nice and neat as I would like to see, and thats aggravating. A lot of the mess stems from excess epoxy squeezing out and making the seams look all lumpy and dumb. A faster clean-up job before anything even begins to think about setting up would have saved me from having stupid looking frames.

First, Ive been having some problems at work that are pretty significant, and I wasnt as focused on gluing as I wanted to be or could have and that led to sloppy gluing work.

Second, I just dont have wood gluing experience. My epoxy/fiberglass experience is solely focused on my Laser, hull #194, from the early 70s. This boat has hit submerged objects, sandbars, docks, buoys, other boats, etc. at speed. Laser speed. Fast. Rig humming with 2/3 of the boat out of the water fast. Once, it fell off my car... while I was driving. Needless to say, Id just slop some epoxy on and keep going. Now that Im gluing together my wood boat, I cant be as messy, or at least, Id rather I wasnt as messy.

BH1 is messy but will be hidden mostly from view. BH2 is somewhat in view and the frames are going to visible, and its kind of messy. BH 3 could have come out perfect, but it looks messy too because I rushed and didnt STOP.THINKFIRST.NOTSOFAST. BH 4 came out really nice and clean, but the frame is mostly hidden within the rear airtight box, so no one will see my clean job! Dammit! Roar!

So heres a tip to you beginners out there: First, read all you can about epoxy. I have yet to find a nice primer/tutorial on wood gluing for boats, and that would have helped. The Storer forum, my thread in particular could help you out. Second, my biggest mistake in neatness is that I waited for the epoxy to firm up to a putty and then tried to hack off the excess. This is a mistake. This evening I glued BH4 together, let it sit for a few minutes to excess epoxy oozed out, and just cleaned it right up. Presto besto pesto yum done. A nice neat job. Why I didnt think about this 3 BHs ago, I know not.

About this Blog

The purpose of this blog is to hold an overview and description of the popular yachts in South Africa. Main focus is on locally designed and built vessels, and vessels with a strong South African connection. Initially, we will focus on the classics (Miuras, RCODs, L26s etc) before moving to modern and larger designs. Designers such as Dudley Dix, Angelo Lavranos, Oswald Berckemeyer, Simonis, van de Stadt come to mind, but there are many others.

Credits and many thanks to Roy McBride as the co-instigator of this initiative, and the source of much of the material - especially photos. Roy has a great interest in boats, especially traditional ones, and is active in the industry where he supplies high quality kits for boat construction from leading designers. He is a fountain of knowledge on traditional boats and construction methods. For anyone interested in boats and cruising, you need to see his blog at ckdboats.blogspot.com - it is updated daily with interesting articles on all sorts of things!

Should you wish to see a specific boat featured, are able to supply (or add information) for a given design, or wish to correct any points made in this blog, please email to infomarina@mweb.co.za

Thank you!

Justin Phillips
Webmaster, HBYC and SA Yacht Blog

Specificity ahead

Time for a little cleaning up. I took care of a lot of little items that needed doing.

I went back to the kick-ass guys at Maine Coast Lumber and got hooked up with some more cedar, primarily for the chine logs, so I can just keep moving on assembly. I also picked up extra cedar just in case. This hopefully is my last cedar purchase, the stuff is getting pricey. I also picked up a good piece of cedar for the STEM. I bought many feet so I can have many attempts, this I feel, is going to suck.

I also bought:

pumps for the epoxy, dammit, I forgot with my initial order.

inspection ports for the bulkheads.

the sail, holy cow, I just had to press the buy button and be done with it.

Next up:

finish the top frame on the transom, which is out of Douglas Fir, which meant that I had the wood for it all along in the form of that long fir plank. Then, when the pumps come in I can glue and epoxy this piece all up.

frame the remaining bulkheads

glue together el bottom and el side-os. This will mean chine longs. I found a 17 foot long piece of cedar, but it was a weird dimension that was going to have to be ripped several times to make it the appropriate size. I have decided to scarf two 9 foot sections together. This will keep one side more uniform (less ripping) and it will teach me a new valuable skill. The scarf joint as spied by gimpslayer3000, but with cedar. This is going to be interesting, because it needs to come out tip-top. Sacramento GIS has built a scarfing jig, which is a fascinating idea, but Im really not interested in that, but it would probably be the best bet for the cleanest scarf. Im wondering about how precise I can get on my own...

and then at some point... the dreaded STEM.

Thats it for now, on the road again. Waiting patiently.