More gaps between BHs and bottom

Today I planed down the chinelogs to flat, in order to fit the bottom at some point in the near future. Unfortunately for me, something somewhere didnt add up.

When I cut the notches in my BHs, I was very careful to use an actual slice from my chinelog to trace a pattern for the notch. Somehow, my notches were too deep laterally, I have gaps there that need filling. Today I now realize that they are also too shallow vertically... after planing the chinelogs flat, I have a gap between the bottom of the BHs and the chinelog. Take note from BH3:


When I fit the bottom onto the boat, the gap is clear (boat is upside down):


This is especially frustrating because:

1: I measured the notches using an actual piece from the chinelog
2: I was very careful to do my best eye-balling job that the bottom of the ply appeared to meet the bottom of the BHs

In retrospect I should have:

1: After the dry-fit turn the hull upside down to get a good look at what was going on
2: Do a test plane portion to see where a flat chinelog ends up in relation to the BHs

So now I can do one of three things:

1: Fill the gap with loads and loads of epoxy when I put on the bottom
- Risky because I could deform the bottom if I screw too hard placing it into position
2: Fill the gap with a strip of wood that is painstakingly cut and glued into place
-Annoying work, AND it wont match the BH bottom frame
3: Continue to plane down the chinelogs until they match the BHs.
-I lose freeboard AND it could make the boat too wide at the bottom and the pre-cut ply for the bottom wont be able to accomodate the new width.

For all its worth, heres the boat with the bottom kinda on:


Ive just decided that solution #3 is not a good one.

I have now just decided to go with option #2.

Interestingly enough, BH1 came out perfect!... WTF, Over?

Slow going

More slow going here in NH, very very little has been accomplished as of late. Between work, 5 F. deg. temps, and a sore back, Ive been laying off my boat for a bit.

In the meantime check out my compatriot in CA!

The GIS fleet is building, people are getting STOKED, sailing will be going down! What are YOU waiting for!?!?

Getting small items done

Slowly but surely, carefully, things are coming along!

My second gunwale is scarfed and glued! As you can see, the epoxy will glue your bricks to the wood too! I had to chisel the brick off the wood, and it left brick behind which was further chiseled. This is my nicest, tightest scarf to date... on this side. Little more of a gap on the other side which is too bad, because the tight side will be glued to the boat due to a curvature in the wood that already nicely conforms to the hull.


My mast step and mast partner are glued up, in place, and ready to be cut open to fit the mast and then glued down. I doubled up the mast partner because the top of BH2 can be easily twisted by hand. By doubling it up, it stiffens it considerably. This makes me feel better after the chaotic gluing job around these bulkheads:


My bow knee came out well except for two things 1. I forgot that it was to be placed OVER the stem. My stem comes up to the edges of the ply, no room to slip it over. This means I will have to either slip it behind the stem or on top of it. I will ask Storer for recommendations. My bow was also considerably wider than the number provided by Storer for the knee. I would highly recommend tracing real world bow to your piece of lumber prior to cutting. Remember to keep the gunwales fastened. My stern knees, by comparison, came out great (I traced the real deal and did not go by the numbers provided by Storer). The great thing about my stern knees is that they are interchangeable, as in, both corners are the same! Yes! Precision building yes! Notice my mail. This is where I throw my bills. Then when I glue on the aft seat, they will be sealed in forever, and all my financial problems will disappear!

Because my workshop is a walk from my assembly point in the garage, my hull is becoming my new holding bin/workshop.


Its also dusty in there! My lonesome bike, covered in wood dust. Primarily this dust is from the wood cherry countertops being built by my brother in law right behind me, but the picture is cooler if everyone thinks its coming from my boat!


In addition,

1. my side arms for BH2 and 4 are cut and beveled to the sides (again, I waited until I got my boat assembled to match them to the actual hull)

2. inwale spacers are cut

I would like warmer temps in the garage before I start gluing things. As of right now, strictly hull, non-gluing, I need to do the following:

1. Cut out the mast holes in the partner and step

2. Scarf inwales

3. Finish fitting bow seat (waiting for gluing of seat cleats)

Other than that, rudder, daggerboard, mast and spars, centerboard trunk.

I am very close to having a totally completed hull.